Print Strike-Offs: How to Approve a Digital Print Sample Before Bulk
Table of Contents
- Introduction
- What a Strike-Off Is, and Is Not
- Screen versus Digital: Why the Route Changes the Approval
- Colour: The Check That Fails Most Often
- Scale, Repeat and Placement
- Hand Feel and the Base Cloth
- The Approval Workflow That Survives a Dispute
- What Can Still Change in Bulk, and How to Cap It
- What a Strike-Off Costs and Why
- Common Disputes and How to Prevent Them
- Our Digital Line and Sampling Terms
- Frequently Asked Questions
- Standards and Test Methods Cited
Introduction
The most expensive sentence in custom printing is "the sample looked fine." Fine on a screen, fine in the factory corridor, fine under a light the garment will never see again. Then bulk arrives, the coral is orange, the leaves are the size of dinner plates, and everyone reaches for the email thread - which says, in effect, that someone looked at something once.
A strike-off handled properly is not a courtesy sample. It is the physical contract for the bulk run: the one object both sides have signed, that colour instruments can be pointed at, and that settles arguments without lawyers. Handled casually, it is a photograph of good intentions. The difference between the two is a checklist, and it fits in this article.
We print digitally in Keqiao and we sit on both sides of this table - approving our own strike-offs to customers, and approving base-cloth and ink performance with our suppliers. What follows is how the approval works when it works.
What a Strike-Off Is, and Is Not
A strike-off is a short length of the actual base cloth, printed with the actual artwork, on the actual machine line that will run bulk - approved for colour, scale, repeat, placement and hand. It is not a lab dip (that approves a single solid colour), not a paper proof (that approves the artwork file), and not a photo (that approves nothing, as we will see).
The distinction matters because each document kills a different risk. The paper proof kills wrong artwork. The lab dip kills wrong solid colour. The strike-off kills wrong print - the interactions between colours, the scale on cloth, the hand after printing. Programs that skip the strike-off and approve from proofs discover the difference at bulk, where the discovery costs a season instead of a courier fee.
Screen versus Digital: Why the Route Changes the Approval
Under rotary screen printing, every colour is a physical screen, so a strike-off commits real money per colour and the approval conversation is dominated by colour count and separation quality. Digital printing removes the screens entirely: any artwork, any colour count, no plate fee. The approval conversation shifts accordingly - away from "can we afford another colour" and toward the things digital does not forgive: base-cloth whiteness, ink gamut on saturated neons, and the discipline of the approval itself.
This shift changes what a buyer should spend time on. With screens, most of the argument is before the strike-off. With digital, the strike-off is fast and cheap - on our line, sampling runs from one metre - so the bottleneck becomes the buyer's own checking discipline. The process got easier; the approval did not get optional.
Colour: The Check That Fails Most Often
Colour on a strike-off is checked against three references, in order. First, the artwork's intended values, ideally as physical swatches or a recognised standard - screen RGB values are a language nobody's printer speaks natively. Second, any previous production you are matching. Third, itself: the design's internal colour relationships, which often matter more to the eye than absolute values.
Then check it under the right light. Metamerism - two recipes matching under one illuminant and diverging under another - is the classic strike-off trap. Approve under the light your customer will use: D65 for daylight-led markets, TL84 or store lighting for retail-led ones, and write the approval illuminant into the order. A strike-off approved under factory fluorescent and sold under retail LED can match the standard and still look wrong on the rack.
A mill-side note on saturation: very bright neons and some deep violets sit near the edge of textile ink gamut. A good printer flags these at the proof stage and shows you the achievable version on cloth, rather than letting you discover the gap at bulk. If your design lives on fluorescent accents, ask for the gamut conversation before the strike-off, not after.
Scale, Repeat and Placement
Scale is the silent killer. A motif that reads charming at A4 becomes overwhelming on a 140 cm width of cloth, and a delicate all-over becomes visual noise at garment distance. Check scale on the physical strike-off, at arm's length, ideally pinned to a dress form or held against the intended garment size. Numbers help: measure the motif and the repeat, write them into the approval, and you have killed the "we thought it would be smaller" dispute before it starts.
Repeat quality is the second check. Follow the pattern across the full width and along a couple of metres: the join should be invisible at normal viewing distance, with no half-motifs stranded at the selvedge that will complicate cutting. If the garment is engineered - placement prints on panels, borders at hems - the strike-off must show the placement exactly as cut, not just the all-over design.
Hand Feel and the Base Cloth
Printing adds chemistry to cloth, and chemistry changes hand. Pigment prints add a slight film; reactive prints keep the base cloth's character but depend on its preparation. Either way, the strike-off's hand is part of the approval: drape it, crease it, wash it if the garment will be washed. A print that looks perfect and feels like oilcloth is a failed strike-off wearing a good disguise.
The base cloth is the other half of the hand equation, and its whiteness and absorbency move the colour too. Approve the strike-off on the exact base-cloth quality that bulk will use - same composition, same weight, same preparation. A beautiful print on a premium sample base, run in bulk on the commercial base, is how "the colour changed" stories begin.
The Approval Workflow That Survives a Dispute
Photos are for speed, not for approval. The working routine: comment on photographs to kill the obviously wrong versions fast - wrong scale, wrong placement, wrong family of colour. Then approve exactly one physical strike-off, signed and dated on the back by both sides, with half travelling to you and half staying at the mill. Bulk is judged against that object, and only that object.
| Check | How | Pass mark |
|---|---|---|
| Colour vs standard | Light box, approval illuminant (D65 or TL84) | Acceptable to eye vs physical standard; instrument reading recorded |
| Scale and repeat | Ruler on motif and repeat; arm's-length look | Measurements written into approval; joins invisible |
| Placement (if any) | Against the pattern piece | Motif lands where the garment needs it |
| Hand and drape | Crease, drape, wash once | No film-like hand; wash does not crack or dull the print |
| Base cloth | Compare to base-cloth standard | Same quality, weight and preparation as bulk |
| Signature | Sign and date the back, split the sample | One physical standard, two locations |
What Can Still Change in Bulk, and How to Cap It
On the same machine, same base-cloth lot family and same ink set, a well-run digital line holds bulk close to the strike-off - close enough that differences are measured, not seen across the room. The gaps open when one of those three constants moves: a new base-cloth lot with different whiteness or absorbency, a different machine with a different calibration history, or heads due for maintenance.
The caps are contractual and cheap. Write that bulk runs on the approved base-cloth quality. Write that the first metres of bulk are checked against the physical strike-off before the run continues - a ten-minute pause that costs nothing against a container. And keep your half of the strike-off out of sunlight: a faded standard reopens every argument it was meant to close.
What a Strike-Off Costs and Why
Digital printing has no plate fee, so the strike-off costs the cloth, the ink and the machine time - on our line, sampling runs from one metre, and the fee is a fraction of what a screen engraver charges for a single colour. This changes buyer behaviour for the better: you can afford to be wrong twice. Use that. Order the strike-off, be brutal with the checklist, order the corrected one. Two strike-offs are still cheaper than one container of almost-right.
Where the money actually sits is bulk MOQ: 300 metres per colourway, a figure set by dyeing and finishing lots rather than by the printer. Below that length the base-cloth preparation cost stops dividing sensibly, which is why the number survives even though the plate is gone.
Common Disputes and How to Prevent Them
The recurring three, and their vaccines. "The colour is off": prevented by the physical signed standard plus the recorded illuminant - without them the argument is two memories. "The scale is wrong": prevented by measurements written into the approval, not adjectives. "The hand changed": prevented by approving the washed strike-off on the bulk base cloth, so the standard already includes the wash. Notice that all three vaccines live at the strike-off stage. By bulk, prevention has expired and only allocation of blame remains.
A fourth dispute is rarer and entirely self-inflicted: the lost standard. The approved strike-off is filed in someone's drawer, the someone leaves the company, and two years later a re-order is judged against a photograph of a photograph. Treat the signed strike-off like a contract document - registered, duplicated, stored flat and dark - because on the worst day of the program it is exactly that.
Our Digital Line and Sampling Terms
On our digital printing line, design is genuinely unconstrained: any artwork, any colour count, no plate fee - what is listed on the site is simply what is in stock today, not the ceiling of the process. Strike-off sampling runs from one metre, bulk from 300 metres per colourway, and every strike-off we ship carries its measurements and approval notes with it, because we expect to be held to it.
Send the artwork and the target garment - market, base cloth preference if you have one, wash expectation - and we will return a strike-off with the checklist in this article already filled in from our side. Approving it should take you twenty minutes and a light box, and that is the whole point.
Frequently Asked Questions
Is a strike-off the same as a lab dip?
No. A lab dip approves one solid colour on a small swatch; a strike-off approves the whole printed design - colours, scale, repeat, placement and hand - on the actual base cloth. A design can pass every lab dip and still fail as a strike-off because the colours interact, the scale is wrong for the garment, or the repeat breaks badly at the seam. Approve solid colours with lab dips; approve the print with a strike-off. Confusing the two is how a correct blue ends up in the wrong shirt.
Why does my print look different under shop light than in the factory?
That is metamerism: two colour recipes that match under one illuminant diverge under another. Approve the strike-off under the light your customer will use - D65 for daylight-led markets, TL84 or store lighting for retail-led ones - and write the approval illuminant into the order. A sample approved under a factory's fluorescent tube and sold under LED retail lighting can legitimately match the standard and still look wrong on the rack.
How close will bulk be to the approved strike-off?
On the same machine, same base cloth and same ink set, a well-run digital line holds bulk close to the strike-off - close enough that differences are measured with instruments rather than seen across the room. The gaps open when something changes: a new base-cloth lot with different whiteness or absorbency, a different machine, a maintenance gap in the heads. Cap the risk contractually: bulk is printed on the approved base cloth lot family, and a first-metre bulk sample is approved against the strike-off before the run continues.
Should I approve a photo of the strike-off instead of the physical sample?
Use the photo to comment, never to approve. Screens and cameras shift colour unpredictably, and a dispute about a photograph is unwinnable for both sides. The workable routine is: comment on photos to kill the obviously wrong versions fast, then approve one physical strike-off that travels between you and the printer, signed and dated on the back. Bulk is then judged against the physical standard, which is the only version that survives an argument.
Does digital printing really have no colour or design limit?
On our digital line, yes: any artwork, any colour count, no plate fee - what is listed on the site is simply what is in stock today, not the ceiling of the process. The real limits sit elsewhere: in the base cloth's whiteness and absorbency, in the gamut of the ink set against very saturated neons, and in your own approval discipline. Within those, the practical difference between three colours and thirty is zero, which is precisely what digital printing changed.
What is the minimum I can order for a custom print?
Strike-off sampling runs from 1 metre, and bulk starts at 300 metres per colourway, with no plate fee because the digital process has no plate to amortise. The 300-metre figure is a dyeing-and-finishing reality rather than a printing minimum: the base cloth is prepared and finished in lots, and below that length the preparation cost stops dividing sensibly. For trials and capsules, the 1-metre strike-off plus one 300-metre colourway is the standard first step.
Standards and Test Methods Cited
- ISO 105-J03 / CIE DE2000 - Instrumental colour-difference evaluation, the measurement behind recorded approval readings.
- ISO 105-A02 - Grey scale for assessing change in colour, used in wash checks on strike-offs.
- ISO 3668 - Visual and instrumental colour matching of paints and textiles, covering illuminant choice such as D65 and TL84.
- ISO 105-C06 - Colour fastness to domestic and commercial laundering, the wash reference for the hand-and-wash check.
Have an artwork ready? Send it with the target garment and market - we return a strike-off with measurements and approval notes already filled in.