Velvet MOQ Explained: Why 300m and 3000m Differ
In this guide
- The four fixed costs behind every minimum
- Why 300 metres is the common floor
- Stock versus custom: two different games
- What is negotiable — and what is not
- Reading a supplier's MOQ answer
- Structuring an order that does not fill a lot
- The price curve: what changes at each quantity
- Writing the MOQ into the PO
Every velvet buyer meets the same wall in the first conversation: the mill's minimum. Three hundred metres per colour sounds arbitrary until you stand at a dye machine and watch what a short run does to colour consistency. This guide explains where the minimum comes from, why it differs between stock and custom fabric, what is negotiable and what is physics, and how to structure an order when your programme does not naturally fill a dye lot.
The mills that answer "we can do any quantity" and the mills that answer "three hundred metres per colour, and here is why" are usually different kinds of suppliers. Understanding the arithmetic behind the second answer is what separates a buyer who negotiates well from one who just pays a premium and hopes.
The four fixed costs behind every minimum
A minimum order quantity is not a policy; it is the point where a production run stops losing money. Four cost centres scale with the run, not with the metres:
- Loom setup and warp changeover. Before the first saleable metre, the warp is beamed, threaded and tensioned — hours of machine time plus yarn that never reaches the invoice. A short run spreads that cost across too few metres.
- The dye lot. A dye machine works by liquor volume. Below a minimum bath fill, take-up becomes uneven — the first metres and the last metres of the run come out different shades, and there is no way to inspect your way out of a fabric that changed colour halfway through the roll.
- Quality control. Pulling test swatches, running lab checks, documenting results — the cost is per run, not per metre. A 50-metre run carries the same QC overhead as a 3,000-metre run.
- Finishing stability. Stenter and finishing lines need batch volume to hold steam and temperature steady. Very short batches produce inconsistent hand across the piece length.
For pile fabrics the dye lot dominates. Velvet dyed in a short bath shows shade drift along the piece far more readily than flat weaves, because the pile surface amplifies any unevenness in dye distribution. That is why a velvet minimum is usually quoted per colour — the constraint lives in the dyeing step, not the weaving step.
Why 300 metres is the common floor
The number traces to dye chemistry. An industry-standard dye machine needs a bath of roughly 60 to 80 kilograms of liquor to run evenly; at velvet's weight per metre, that bath volumes out to a few hundred linear metres of fabric. Below that, the mill has two choices: run the bath half-empty and accept uneven take-up, or hand-dye the lot in small equipment with no lot-to-lot repeatability.
Some suppliers will quote 50 metres on a custom colour. Read that quote as one of two things: a hand-dyed small lot that will never be repeatable on reorder, or your order pooled into another client's dye run — where your colour shares a bath with theirs and drifts with whatever else is in it. Neither scenario ends well for a programme that needs a second production run to match the first.
The honest structure most mills converge on: 300 metres per colour for custom-dyed fabric, where the bath fills properly and the recipe is archived for reorder; and much lower or zero minimums for stock shades, where the dyeing already happened at the mill's own risk. If your programme can live inside stock colours, you sidestep the entire conversation.
Stock versus custom: two different games
| Stock (running shades) | Custom (dyed to your colour) | |
|---|---|---|
| Minimum | Low or none — buy by the metre | ~300 m per colour |
| Price | Lowest per metre; setup already absorbed | Higher; setup amortised across your run |
| Colour choice | What's on the shelf | Your Pantone, matched and archived |
| Lead time | Days | Sampling rounds plus bulk production |
| Reorder risk | None while stock lasts | Low if the recipe is recorded; ask to confirm |
The practical consequence: the cheapest way to fill a small programme is often two or three stock shades rather than one custom colour, even though the custom colour is the one you "really want". The most expensive way is a 100-metre custom order at a surcharge, because you pay the setup either way and carry the colour-drift risk too.
What is negotiable — and what is not
The dye bath floor is physics; everything around it is negotiation:
- Negotiable: the structure. Quantity-tiered pricing, combining two designs in one production window, or running your custom colour on a stock base so the yarn lot is shared — all of these lower your entry point without asking the mill to run an impossible bath.
- Negotiable: the surcharge. Some mills accept below-minimum custom runs at a price premium — commonly 15-30% above the base rate — because the setup is real and someone must pay it. A transparent surcharge on 200 metres can be cheaper overall than buying 300 metres you will not sell. Ask for the surcharge in writing, not buried in the per-metre number.
- Negotiable: pooling. If a mill runs the same base for several clients, your 100 metres can join a larger dye window of your exact shade — zero extra setup, full-bath consistency. This is a legitimate and underused route; ask whether your shade overlaps anything in the current schedule.
- Not negotiable: the bath itself. A mill that claims to custom-dye 50 metres in a full-size machine at standard price is either mistaken or pooling without telling you. The arithmetic does not move because the conversation does.
- Not negotiable: archive the recipe. Whatever the run size, insist the dye recipe is recorded against your colour code. The minimum exists partly so that a reorder can match; a first run with no archived recipe is a one-time purchase wearing a reorder's clothes.
Reading a supplier's MOQ answer
The way a supplier handles the minimum question tells you what they are. Useful probes:
- Ask for the run sheet. Request the dye lot size in kilograms for your order. A direct mill answers from the schedule; a trader improvises.
- Ask what happens below minimum. "We can't, but here are two structures that get close" is the professional answer. "Sure, send us 50 metres" with no explanation is a flag — something downstream of you is absorbing risk you cannot see.
- Ask about reorder matching. For custom colours, the question that matters is not "can you make it" but "can you make it again, identically". The answer should reference the archived recipe and a colour tolerance against the approved standard — a ΔE figure or a named tolerance scale, not a promise.
- Ask about the per-metre price curve. Real production pricing has steps at specific volumes, where setup costs change hands. A quote that is suspiciously linear from 50 to 5,000 metres has not been built from the mill's actual cost floor.
Structuring an order that does not fill a lot
When your programme genuinely needs less than the minimum, work the options in this order:
- Stock shades first. Take the core colours from running stock at no minimum; save custom development for the one colour that carries the collection.
- Consolidate the palette. Three custom colours at 300 metres each is a different business from eight at the same minimum. Merging near-identical shades before quoting is the highest-leverage decision a small programme makes.
- Pool or piggyback. If your shade matches a run already scheduled, joining the window costs the mill almost nothing and often costs you the standard rate.
- Pay the honest surcharge. Where pooling is impossible, a stated premium on a shorter run beats stretching to minimum volume that dies in your warehouse — markdown losses reliably exceed surcharges.
- Grey goods + piece dye. For constructions that support it, taking undyed fabric and dyeing in smaller later batches moves flexibility upstream — at the cost of a second production step and its lead time.
The price curve: what changes at each quantity
Per-metre pricing on velvet moves in steps, and knowing where the steps sit makes quotes legible:
- Sample lengths (a few metres). Highest per-metre rate; setup dominates. Understandable as machine-time pricing, not fabric pricing.
- Sub-minimum runs (100-250 metres). Setup spread thin, either as a stated surcharge or hidden in an elevated rate. This is the zone where quotes vary most between suppliers — and where transparency separates them.
- At the minimum (~300 metres). The bespoke spec covers its own setup; the per-metre price stabilises. For most programmes this is the first genuinely production-grade price.
- Full efficiency (1,000 metres and beyond). Continuous production, volume yarn pricing, batched finishing. The per-metre rate drops again — modestly, because dye and setup were already amortised; the incremental savings come from throughput, not setup.
One practical consequence: the difference between a 300-metre run and a 3,000-metre run is real but far smaller than the difference between 100 metres and 300 metres. Buyers who stretch to a minimum they cannot sell "to get the good price" usually lose on markdown more than they gain per metre. The quantity question is a sell-through question first and a pricing question second.
Writing the MOQ into the PO
Three clauses prevent the classic disputes:
- Minimum and per-colour basis, stated. "Minimum 300 metres per colour per construction" — because per-colour and per-order minimums are different commitments, and orders fail on the gap between them.
- Reorder tolerance, stated. The reorder must match the approved standard within a named colour tolerance; the approved lab dip or pre-production sample is the master, archived at both ends.
- Surcharge, transparent. If any run falls below the stated minimum with a premium applied, the premium is a line item, not arithmetic hidden inside a per-metre price.
Two final notes on colour counts. First, the minimum is per colour, not per order — an order of 300 metres split across six shades fails the per-colour test even though the total looks right, and programmes fail on this gap more often than on any negotiation. Second, shade merging is a design decision worth making deliberately: two near-identical greys read as one grey to a customer browsing a rail, but they cost two dye lots. The palette review that merges them belongs in the sourcing conversation, not after the quotes arrive.
And when a supplier's minimum genuinely does not fit, the professional move is to say so plainly and ask for their structure anyway — tiered pricing, pooled windows, stock alternatives. Suppliers remember buyers who understood the constraint and worked with it, and that memory prices every later order.
The buyers who treat the minimum as a design constraint — palette consolidation before negotiation, stock shades where they work, custom colour where it earns its setup — spend less per metre than the buyers who fight the number. The minimum is not the mill's gate to argue past; it is the size of the machine, and it was there before you asked.
Frequently Asked Questions
Why do velvet mills require 300 metres per colour?
The dye machine needs a full bath - roughly 60 to 80 kilograms of liquor - for even dye take-up. At velvet's weight per metre that bath volumes out to a few hundred linear metres. Below it, the mill either runs a half-empty bath with uneven take-up or hand-dyes a lot that will never repeat identically.
Can I order less than the minimum?
Sometimes, at a stated surcharge - commonly 15 to 30 percent above the base rate - because the setup cost is real and someone must pay it. A transparent premium on 200 metres is often cheaper overall than buying 300 metres you will not sell. Insist the surcharge appears as a line item, not inside a per-metre number.
Why is stock fabric cheaper per metre?
The dyeing, setup and QC costs were already absorbed when the mill produced the stock at its own risk. You pay only marginal handling, which is why stock shades carry low or no minimum and the best per-metre price - trading away colour choice to get it.
What happens to shade consistency on a short dye run?
It drifts. The first metres and the last metres of an under-filled bath take dye differently, and on pile fabric the difference is more visible than on flat weaves. That is why the minimum is quoted per colour - the constraint lives in dyeing, not weaving.
Can two designs share one dye minimum?
Not the bath, but the window: mills often book two designs into one production schedule, or run your custom colour on a shared stock base, to spread setup across orders. Ask what is currently running - a shade that overlaps an existing window can join at the standard rate.
Will a reorder match my first run?
Only if the recipe was archived. Insist the dye recipe is recorded against your colour code and that reorders must match the approved standard within a named tolerance. A first run with no archived recipe is a one-time purchase wearing a reorder's clothes.