Velvet Sampling: How Long, How Much, What You Get

Stacks of colour swatch cards at the sampling bench, where lab dip approvals are decided

Sampling is where fabric programmes are won and lost, and it is the stage buyers most often mis-plan — because "get a sample" is actually four separate approvals with different clocks, different costs and different failure modes. This guide walks the full chain from colour reference to pre-production lot: what each stage proves, what it costs, how long it takes, and the writing-down rules that keep a bulk order from arriving different from the sample that won the order.

The four approval gates

Sampling is not one event. Treating it as one is why launch calendars slip and why repeat orders drift from first approvals. The gates, in the order they must close:

  • Gate 1 — lab dip. Small dyed swatches matched to your colour reference. This locks the colour recipe. Approve under defined lighting, in writing, with a sealed master retained by both sides.
  • Gate 2 — sample yardage (strike-off / handloom). A short length of the actual construction, dyed and finished. This proves the fabric: hand, weight, drape, opacity, pile behaviour — on the real cloth, not a paper standard.
  • Gate 3 — test and tolerance sign-off. The measurement rules for bulk: named test methods, sampling frequency, acceptance numbers for shrinkage, colour fastness, weight tolerance, defect level. Three to five working days of paperwork that decides every later dispute.
  • Gate 4 — pre-production lot. The first bulk-scale dye lot, sampled and tested against gates 1-3. This is the release gate: bulk proceeds, and the pre-pro standard becomes the reorder baseline.

Each gate releases a different risk. Skipping gate 3 because gates 1-2 "look fine" is the most common shortcut, and the reason colour and shrinkage claims arrive without rules to judge them by.

What each stage costs and takes

StageTypical timeTypical cost basisWhat it proves
Swatch card / sample cardDaysFree to courier cost onlyConstruction exists; initial filtering
Lab dip3-7 working days per roundCharged per colour; often credited on bulkThe colour recipe; expect two rounds
Sample yardage5-10 working daysPer-metre rate well above bulk; setup amortised over few metresFabric behaviour: hand, drape, pile, wash
Pre-production lotRuns with bulk schedulingPart of the bulk orderRecipe scales; reorder baseline

Two structural facts explain the pricing. First, sample yardage costs more per metre than bulk because setup — warping, dye bath, changeover — is amortised over a few metres; you are paying for machine time, not fabric. Second, mills that advertise free sampling have usually built the cost into the bulk price as a small markup across the whole order; a transparent sampling fee is almost always the cheaper structure once you run the arithmetic on a real order size.

Sample fees credited against the eventual bulk order are common and worth asking for — it aligns the supplier's incentive with your progression instead of making sampling a profit centre.

How long sampling really takes

For an existing construction in a new colour, the full chain from reference to approved pre-production standard runs roughly two to four weeks when nothing goes wrong, plus bulk production after it. For a new construction, add development sampling on the front end. The schedule killers are predictable:

  • Screen colour references. A Pantone code sent as a screenshot costs a round trip almost every time. Send a physical chip or garment, or spectrophotometer data alongside the physical standard.
  • Multiple dip rounds. Two rounds is normal; each correction adds a week. Rounds multiply when the reference is ambiguous or the substrate changes mid-process.
  • Specification drift. Changing weight or composition after the lab dip restarts the chain from strike-off. Freeze the spec before gate 1.
  • Seasonal load. Development queues lengthen ahead of peak production windows; a sampling request in the run-up to a holiday production rush sits behind bulk commitments.

Plan the calendar backwards from the cutting date: bulk production plus transit plus inspection all sit after sampling, so a programme that needs fabric on the cutting floor in twelve weeks should have approved lab dips before week six.

What a sample can and cannot prove

A swatch proves construction. It cannot prove:

  • Garment-scale behaviour. Seam puckering, pattern alignment and drape on real panels only show on sewn trials — which is why sample yardage should be tested in your actual garment, not on a table.
  • Lot-scale consistency. A single dip is one bath; bulk is many. The pre-production gate exists precisely to catch the gap between the bath that won the order and the baths that ship it.
  • Lighting-true colour. Pile fabrics shift hue with light angle and temperature — a shade that reads neutral under cool LED can skew green under warm interior lighting. Approve colour under the light source your product will actually live in, and for velvet specifically, view the sample at multiple angles.
  • Wash performance. Run the wash-and-shrinkage test on sample yardage, not on the swatch: shrinkage, colour bleed, pile matting after the cycles your care label will claim.

How to approve — the writing-down rules

Every approval that matters is a document, not a conversation:

  • Sign the lab dip. Approved in writing, reference code recorded, one sealed copy with you, one with the mill. "Looks good" in a chat window does not survive a bulk dispute.
  • Name the lighting. Approval under a defined source (daylight-equivalent and store-lighting as a minimum pair) — and record it on the approval, because a colour standard without its lighting condition is half a standard.
  • Attach numbers to gate 3. Shrinkage limits per direction, fastness grades per test, weight tolerance, defect classification. Named methods and numbers, or the inspection has nothing to inspect against.
  • Seal the pre-production standard. The first bulk lot's approved sample becomes the master that every later lot and every reorder is judged against. Both parties keep a sealed copy; the recipe archive references it.

Velvet-specific sampling notes

Pile fabrics add three items to the standard checklist, and all three cost nothing but attention:

  • Pile direction on the sample. Mark the nap direction on sample yardage; shade judgement depends on viewing angle, and an unmarked sample gets re-read differently by every reviewer.
  • Crush recovery check. Fold, press and rub a section of the sample yardage, then steam it: does the pile recover? This single test catches constructions that look perfect and die in a suitcase.
  • Depth-of-shade effects. Dark shades carry more dye load and behave differently in fastness tests. If the programme runs navy and beige, both colourways deserve their own dip approval — a family certificate approved on beige says nothing about navy.

Remote approvals: when photos work and when they fail

Most sampling happens across borders, so the question of what can be approved from a screen matters. The honest split:

  • Acceptable remotely: construction checks (weave, weight estimate against a known reference), obvious defect screening, pile direction marking, and gross colour errors — a dip that is clearly the wrong family is rejectable from a photograph taken in daylight.
  • Never remotely: final colour approval. Pile fabrics shift hue with angle and light temperature; a photo flattens both variables. The signed lab dip approval needs the physical swatch in hand, viewed under the named lighting conditions, before bulk commits.
  • The hybrid that works: photo screening to catch obvious misses fast, courier the physical dips in parallel, sign on paper. The photos save a week on clear rejections; the courier cost is trivial against a bulk order placed on a screen judgement.
  • Video for pile behaviour: a short clip of the sample tilted through the light angle shows shade movement and crush recovery better than any still. Ask suppliers for tilt videos on pile fabrics as a standard attachment — the request itself signals a buyer who will check.

What sampling actually costs on a two-colour programme

Assembled honestly, a typical two-colour sampling budget on an existing construction includes: courier for the initial swatch card; lab dip fees for two colours, doubled for the normal one revision round; a short length of sample yardage per colour at the elevated per-metre rate, plus its courier; and the wash-testing on yardage — whether run in-house or at a third-party lab, which adds a lab fee per test but produces the documented numbers that gate 3 needs. Against a bulk order, this sampling spend is small; against the risk of a bulk order placed without it, it is negligible. The failure mode worth fearing is not the cost — it is the programme that skips a gate to save a week and spends a season absorbing the result.

What to send with the first sampling request

The brief that accompanies a sampling request decides how many round trips the chain takes. The complete first message contains: the end garment and target market; fibre, weight and width targets (or a reference fabric to match); a physical colour reference or spectrophotometer data; the care claims the label will print, since they set the wash-test conditions; expected quantities, so the mill sizes the development properly; and the target date, stated as the fabric-on-cutting-floor date rather than the order date. A brief with all six arrives at the front of the lab queue and usually saves one full dip round — which is to say, a week.

Also worth sampling deliberately: the backing. On some constructions the pile and backing differ in fibre, and sample yardage is the only stage where the two can be examined together — check the back for weave quality, stiffness and shrinkage behaviour alongside the face, because bulk disputes about hand and lay-flat almost always trace to the backing, not the pile. A mill that resists supplying yardage with backing information is telling you something about where its construction weaknesses live.

The sampling timeline, assembled

Assembled for a repeatable construction in two colours: swatch card week one; lab dips two rounds, weeks two to four in parallel with the sample-yardage loom slot; yardage testing and gate-3 sign-off week five; bulk scheduling and pre-production lot weeks six onward. First samples rarely pass unchanged — build one revision round into every plan and be pleasantly surprised when it isn't needed.

The buyers who move fastest are not the ones who skip gates. They are the ones whose briefs are complete on day one, whose colour references are physical, and whose approvals are documents — because every one of those removes a round trip from a chain where each round trip costs a week.

One closing habit worth adopting: keep a sampling log per programme — dates requested, received, approved, per gate, per supplier. Two seasons in, the log becomes a per-supplier reliability record better than any marketing claim: which one's dips land in five days, which one needs three rounds, which one's bulk matched its pre-pro standard. Sampling discipline is partly a quality tool and partly a sourcing intelligence system; the buyers who log it never re-learn the same supplier the expensive way.

Frequently Asked Questions

How long does velvet sampling take end to end?

For an existing construction in a new colour, roughly two to four weeks from reference to approved pre-production standard, plus bulk production after. Plan one revision round - two lab dip rounds is normal - and work the calendar backwards from your cutting date.

What is the difference between a lab dip and sample yardage?

A lab dip is small dyed swatches proving the colour recipe; sample yardage is a short length of the actual construction proving the fabric - hand, weight, drape, pile behaviour. Colour is approved first, then the yardage; approving both at once risks knitting metres of fabric in a shade you will reject.

Why do samples cost more per metre than bulk?

Setup - warping, dye bath, changeover - is amortised over a few metres, so you are paying for machine time rather than fabric. Mills advertising free sampling usually recover the cost as a markup across the bulk order instead; a transparent fee is often the cheaper structure.

What lighting should I approve colours under?

At minimum a daylight-equivalent source plus the store lighting your product will sell under, recorded on the approval. Velvet adds a wrinkle: pile shifts hue with viewing angle, so view the sample at multiple angles before signing.

What tests should run on sample yardage?

Wash and shrinkage at the cycles your care label will claim, colour fastness on the darkest colourway you plan to run, and for velvet specifically a crush-recovery check: fold, press and rub a section, then steam it and see whether the pile stands back up.

What is a pre-production sample and do I need one?

The first bulk-scale dye lot, tested against your approved lab dip and tolerance sheet. It is the gate that catches the gap between the bath that won the order and the baths that ship it - and its sealed standard becomes the baseline every reorder is judged against.

✉ Inquiry 📱Chat on WhatsApp