Table of Contents


Why velvet takes a mark when other cloth does not

A flat woven cloth can be folded, stacked, compressed and shipped, and it arrives ready to cut. Velvet cannot. Its surface is a forest of cut pile ends standing at an angle, and every one of those ends has a direction. Press them flat in one place and the light no longer catches that patch the way it catches the rest — which reads as a mark, a stain, or a shade difference depending on how bad it is.

Two mechanisms produce the mark, and they behave differently. Pile crush is mechanical: the fibres are bent over and stay bent. Pile matting is what happens when crush is combined with moisture and time — the ends pack together and the surface loses its loft. Crush often recovers; matting frequently does not, or recovers only partially and unevenly.

That distinction matters commercially because it decides who carries the loss. A crushed roll that recovers after a day on a table is a scheduling inconvenience. A matted roll is a claim.

Roll or fold: the choice that decides how it arrives

Velvet should travel rolled, pile outward, on a core. Folding puts a hard crease across the full width at every fold, and a crease in pile is the worst case: it is compressed along a line, and the line is exactly where a cutting marker will want to place a panel.

Rolling with the pile outward does two things. It keeps the pile surface on the outside of the roll, where it is not pressed against itself, and it means the only contact is between pile and the roll's own outer layer — a soft-to-soft contact rather than pile against a carton wall. Rolling pile inward puts the pile against the core and against itself across the whole length, and the inner layers take the load of the entire roll.

If a roll must be stacked on a pallet, stack them upright rather than laying them horizontally on top of each other. A horizontal stack puts the weight of every roll onto the pile surface of the one below, over the full length. The bottom roll of a four-high stack is the one that generates the claim.

Roll diameter and core: the number nobody specifies

Two numbers decide whether a roll arrives clean, and neither is normally written on a purchase order. The first is roll diameter. A tight roll bends the cloth through a small radius, which compresses the inside of the bend and stretches the outside — the tighter the roll, the more pronounced the effect, and the longer it sits the more permanent it becomes.

The second is core diameter. A small core forces a tighter bend at the centre of the roll, where the compressive strain is highest and where the cloth sits longest. Moving from a small core to a larger one costs a little in packing volume and removes the worst of the problem before it starts.

The practical instruction is a maximum roll length rather than a maximum diameter, because length is what a buyer can count and what a packing list can state. Specify a maximum metres-per-roll and a minimum core size, and let the mill choose the diameter that satisfies both. Typical export practice for a 250 GSM velvet is to keep rolls to a length where the finished diameter stays within a band the carton can take without compression — and the mill knows that band for its own cloth.

Our own shipping standard for velvet is to roll pile-outward on a core and to avoid compression packing. What that means for a specific order is settled at booking, and it is worth settling in writing rather than assuming.

Recovery: what steam can and cannot undo

Recovery is real but limited, and buyers routinely over-estimate it. Three factors govern how much comes back:

  • Time under load. A crease held for a week recovers less than one held for a day. This is why storage duration matters as much as storage method.
  • Moisture. Dry crush recovers better than crush that has been damp. A humid container is worse than a dry one, and a roll that has crossed an ocean in a humid container has effectively been matted, not just crushed.
  • Fibre. A viscose-rich pile at 80/20 behaves differently from a polyester pile. Viscose takes up moisture and holds it, which makes matting more likely under humid conditions; polyester resists it but can take a sharper set when crushed hot.

Steam is the standard recovery tool, and it works by relaxing the fibre so the pile can stand back up. It works best on fresh crush and worst on old matting, and it never restores a surface to exactly what it was. A buyer who receives a marked roll should treat steam as a mitigation and not as a remedy, and should inspect before cutting rather than after.

The one thing steam cannot fix is a mark that has changed the shade rather than the loft — where the pile has been permanently laid in a different direction from its neighbours. That is a directional problem, covered in the pile direction and shade variation guide, and it is not recoverable by any finishing route.

Specification

ParameterMJ-VSL01 solidBurnout (devoré)MJ7124 stretch
Composition80% viscose / 20% nylon80% viscose / 20% nylon95% polyester / 5% spandex
WeightApprox. 250 GSMPile and ground, pattern-dependent250 GSM
WidthStandard velvet widthStandard velvet width155–160 cm
Colour range24 stock colours + 40-colour standard card73 designs, BR-01 to BR-7376 colours
FOB priceFrom USD 3.20 per mFrom USD 3.10 per mUSD 2.10–2.35 per m
MOQ300 m300 m per design300 m
PackingRolled pile-outward on coreRolled pile-outward on coreRolled pile-outward on core
Colour approvalStandard light source, before shipmentStandard light source, before shipmentStandard light source, before shipment

The burnout construction is the one that needs the most care in packing. Because the pile is removed in the pattern areas to expose the ground, the cloth has two different surface levels, and the boundary between them is where crush shows first. A burnout roll packed under compression will show the pattern edges as a ghost line long after the flat areas have recovered.

The export packing spec

Five lines belong in the packing instruction, and they cost nothing to write:

  1. Rolled, not folded, pile outward, on a core of stated minimum diameter.
  2. Maximum metres per roll, which caps the finished diameter.
  3. No compression packing — no vacuum bags, no over-tight cartons.
  4. Upright pallet stacking, with rolls standing rather than laid horizontally on each other.
  5. Moisture protection — a liner inside the carton, because humidity does more lasting damage than weight.

Two further points belong in the commercial terms rather than in the packing spec. First, inspect on arrival and before cutting, because a mark found after the marker is laid is a mark you have already paid to cut around. Second, agree in writing what counts as a mark — a shade difference, a pile direction change and a crush line are three different defects and they are usually treated as one in a claim.

For the wider sourcing context on this category, the velvet sourcing guide covers mill selection and the cost structure guide covers how volume changes the economics.

Frequently asked questions

Do pressure marks on velvet come out?

Partly, and it depends on how long the cloth was compressed and whether moisture was involved. Dry crush usually recovers with steam and time; matting from damp compression frequently does not, or recovers unevenly.

Should velvet be rolled or folded for shipping?

Rolled, pile outward, on a core. Folding creases the pile along a line across the full width, and that line is exactly where a marker will want to place a panel.

What roll diameter should I specify?

Specify a maximum metres per roll and a minimum core diameter rather than a diameter directly. Those two numbers cap the bend radius, which is what actually controls crush at the centre of the roll.

Can I vacuum-pack velvet to save freight?

No. Vacuum packing compresses the pile across the whole surface and produces matting rather than crush, which is far less recoverable. The freight saving is almost always smaller than the claim.

How should velvet be stored before cutting?

Rolled, upright, in a dry space, away from direct sun and away from anything resting on the roll. Time under load matters as much as the load itself, so cut from older rolls first.

Decide it before the container

Velvet marks are decided in three places: how the cloth is rolled, how the rolls are stacked, and how long they sit. All three are controlled by the buyer through the packing instruction, and none of them requires new equipment.

Write the roll length, the core size, the no-compression rule and the upright stacking into the order. On a 250 GSM velvet at 24 stock colours and burnout designs run to order from 300 m, the cloth leaving the mill is fine — it is the journey afterwards that puts the mark on it.

Mujia Textile — running our own air-jet looms in Zhuji since 2012.