How to Specify Velvet for a Khimar

Velvet roll held up at the mill with daylight behind it, checking a khimar weight for the glow that shows through single-layer pile

A buyer in Kuwait sends three metres of black velvet and one sentence: it looks solid on the table and goes see-through in the car. The cloth is 230 GSM and nothing about it is defective. It simply passes light, and nobody warned her, because weight is the only number anyone quotes.

A khimar is the wrong garment to specify by weight alone. It hangs from the head down the back, it is worn outdoors, and it is seen against the sun for much of the day. Three properties decide whether it works: opacity, drape and how the colour behaves under wear. Only the last correlates loosely with GSM.

Opacity first, and weight is a poor proxy for it

Velvet looks opaque because the pile scatters light at the surface. That scattering is real, but it happens at the face. Underneath sits a ground structure of roughly 80 to 120 GSM, and the ground is where light gets through.

A dense 180 GSM cloth on a tightly sett ground blocks more light than a loose 240 GSM cloth whose weight comes from longer pile on a thin base. Pile adds depth of colour and surface, not a light barrier. Buyers who order by GSM and test outdoors learn this in the first shipment.

The mechanism matters when the cloth is backlit, which is the khimar condition. Daylight passes the ground, reflects off the skin, and comes back through the pile. In a dark colour most of that light is absorbed on the second pass, but red wavelengths survive better. That is why a thin black velvet reads faintly red-brown against a low sun.

The fix is not a heavier pile. It is a denser ground, a finer count, a tighter sett and — where the end use demands it — a dark yarn in the ground so light that passes is absorbed rather than reflected. All three are weaving decisions, settled before the order.

Testing it on a sample, in the way it will be worn

Lab cards do not show this. A swatch laid flat on a white table looks opaque for every cloth. The test that predicts field behaviour takes two minutes and a phone torch.

Fold the sample once, hold it against a window or a torch in a dim room, and look at what comes through. One layer showing a glow means the cloth reads thin outdoors. Two layers still glowing means it reads thin in any sunlight. Repeat with the sample 30 cm from the light rather than against it, because a khimar hangs away from the body.

For a figure rather than a judgement, ask for transmittance across the visible range. A 400 to 700 nm scan gives a percentage at each wavelength. Below about 5 percent total is solid in daylight; 8 to 12 percent is where customers start to notice. Read the red end, not the average, because that band produces the brown cast.

CheckMethodPassWhat failure looks like
Single-layer backlightSample against a window, dim roomNo visible glowPale halo through the cloth
Double-layer backlightFolded once, 30 cm from a torchNo glow at allShadow of fingers visible
Transmittance scanSpectrophotometer, 400–700 nmUnder 5% totalPeak above 600 nm (red leak)
Sun testWalk outdoors at midday, facing the lightSilhouette does not readShoulder line shows through

Drape: it has to fall, and it must not cling

A khimar has no fastening below the head. It holds its shape by its own weight and by how the cloth moves, which puts two opposing demands on the fabric: it has to fall in a soft vertical line, and it must not stick to what is underneath.

Drape is measured as a coefficient, from about 30 percent for a stiff cloth to 80 for a fluid one. Pile fabrics sit in the middle; the working band for a khimar is 55 to 70 percent. Below that the cloth stands away like a hood. Above it the cloth collapses against the shoulders and shows every line underneath.

The cling problem is separate and usually blamed on thinness. It is more often static. Polyester pile generates charge readily, and a charged cloth pulls towards the body instead of hanging free. Anti-static finishing reduces it, as does higher moisture regain in the ground yarn, but neither is permanent. Specify how many washes the finish must survive: one that dies after ten becomes a complaint six weeks into the season.

Hand feel is the fastest proxy in the sample room. Take the sample by one corner, let it hang, and watch the fold. Narrow soft folds hang well; two or three broad stiff folds stand away. Then rub it against a wool sleeve and see whether it lifts.

The weight that matters is per garment, not per square metre

GSM describes the cloth; the wearer feels the garment. A khimar carries its whole weight on a band around the head, roughly 56 cm in circumference, pressing on the forehead and crown for eight or ten hours.

The arithmetic is simple once the panel size is known. A common cut is about 1.5 m long by 1.4 m at the base, a little over two square metres. At 200 GSM that is roughly 420 g hanging from the head; at 260 GSM, 550 g. The 130 g difference sounds trivial in a warehouse and is not trivial at hour six.

Pile weight also shifts through finishing more than a flat cloth does. A 220 GSM greige can leave the mill at 205 or 240 depending on how much pile is cut back. Ask for the weight on the finished, relaxed sample, and for the panel weight of the cut you are making.

The practical band is 180 to 240 GSM finished. Below 180 the cloth needs an unusually dense ground to stay opaque and rarely drapes well. Above 240 the garment becomes a weight on the head and the shoulder fold turns into a shelf rather than a line.

Which way the pile faces changes the whole garment

Velvet has a face and a back, and the difference is not cosmetic. Pile out is conventional for a khimar: the surface catches light softly, the colour reads deep, and the cloth glides over hair because the tips present little friction in one direction. Pile in gives a smoother surface against the skin and sheds less onto clothing, but the outside reads flat and slightly dull.

Whichever is chosen, every panel must be cut the same way up. A panel cut against the nap reflects light differently, and on a garment seen in motion the two halves of a back panel read as two shades. In daylight this is obvious and under tungsten it is invisible, which is why it passes inspection and fails in the street.

The mechanics are set out in the guide to pile direction and shade variation, including how to lay a marker when the pattern cannot be nested both ways. On a khimar the cost is real: a one-direction marker loses 5 to 8 percent of yield, and the loss is not negotiable.

If the garment is lined at the headband, choose the lining for friction as well as comfort. A smooth polyester lining against a pile outer lets the band slide, and a khimar that slides is adjusted all day. The same pile cloth, or a cotton poplin, holds better.

Black is the hardest colour to keep black

Most khimars are dark, and black is the volume colour. It is also the one that shows every pile failure most clearly: a surface rubbed, flattened or worn at the tips reflects more light than an intact one, and on black that reflection reads as grey.

Two things drive it. The first is dye penetration: a fibre dyed all the way through keeps its colour when abraded; one with dye near the surface goes pale where it has worn. Deep black on polyester needs high concentration and time under pressure, and a low-cost black is often a surface black. The second is fibre lustre: bright polyester has a glassy surface that reflects light even when the colour is right, so black on bright yarn reads charcoal. Semi-dull yarn reads deeper at the same dye level.

Rubbing fastness predicts the complaint better than light fastness. A khimar rubs against hair, a coat shoulder, a seat belt and itself where it folds. Grade 4 dry and 3-4 wet is the working minimum for a dark shade; the mechanisms are in the colour fastness guide.

The rest of the range follows the same logic. Deep navy, charcoal, deep brown, olive and burgundy hide a tonal shift because there is depth to absorb it. Mid and light tones — sand, oyster, pale grey — read every compression mark as a shadow. Where a light tone is wanted for summer, the safer route is a matte finish and denser ground rather than a lighter dye on the same cloth.

ColourHides pile marksShows rub marksNotes for a khimar
BlackBestWorst if dye is surface-onlyNeeds semi-dull yarn and full penetration
Navy / charcoalVery goodModerateSafest volume choice after black
Deep brown / oliveGoodLowTonal shift reads as part of the colour
Sand / oysterPoorHighEvery mark reads; needs matte and dense ground

Length is the first thing washing changes

A khimar is cut to a length, and the wearer notices two centimetres at the hem. Pile cloth moves in washing more than a flat cloth of the same composition, because the ground relaxes while the pile holds its structure. The change appears in the first wash and not before.

Untreated woven velvet typically shrinks 3 to 5 percent along the warp in a first domestic wash, and rather less along the weft. On a 1.5 m panel that is 4.5 to 7.5 cm, which is the difference between the garment falling correctly and falling short. Pre-shrunk or compacted finishing reduces the figure to 1 to 2 percent, and that is what should be specified for any khimar that will be washed rather than dry-cleaned.

The question is not the percentage alone but the method behind it. A figure from one wash at 30 °C is not the same as one from five cycles, and customers wash repeatedly. Ask for the third-wash figure as well as the first; the wider treatment is in the shrinkage guide.

The practical answer is a cutting allowance. Whatever the mill quotes, add 3 percent to the panel and let the garment maker trim to final after a test wash of the actual lot, rather than trusting a figure from a previous order.

The hem is where a velvet khimar fails first

A velvet hem cannot be turned and stitched the way a cotton hem can. Two folds give four thicknesses at the edge, the seam goes stiff, and a stiff edge on a soft garment curls. In wear the curl lifts the hem away from the body and the garment loses its line.

Three finishes work. Bias binding, 1.2 to 1.5 cm finished, gives a clean edge and adds a deliberate detail. A close overlock with a narrow rolled hem works on lighter weights but shows a ridge on heavier ones. A faced hem — lining or the same cloth cut on the straight — keeps the edge soft where no stitching should show.

Whichever is used, the pile direction of the binding matters, and the seam should be pressed from the back on a needle board, never flat on the table. A velvet edge pressed flat acquires a shine along its length that nothing removes. The same applies to any headband detail.

How much cloth a khimar order actually consumes

At 140 cm usable width, a 1.5 m panel sits alongside a second if the cut is narrow enough, and practical consumption is 1.7 to 2.0 running metres including hem allowance and shrinkage margin. Waist-length styles, or two-piece versions with an underscarf, add 0.4 to 0.6 m.

Settle the width before the order. Plain velvet in the range comes at 140 cm and, for the plain-dyed qualities, at 160 cm; the wider cloth changes the marker and can cut consumption 10 to 15 percent on a garment this simple. The trade is worked through in the cutting yield comparison.

Against a 300 metres per colour minimum, 1.8 m average gives roughly 165 garments per colour before seconds. That number decides whether six shades or twelve are realistic for a season, and it is worth calculating before the shade card rather than after. Small-order cost behaviour is in the cost structure guide.

StylePanelConsumption at 140 cmPieces per 300 m
Standard shoulder-length1.5 m × 1.4 m base1.7–1.9 m158–176
Waist-length1.9 m × 1.4 m base2.1–2.3 m130–143
Two-piece with underscarf1.5 m panel + 0.6 m scarf2.3–2.6 m115–130

Six lines that prevent most of the returns

A khimar specification does not need to be long. It needs to name what a mill cannot guess.

  1. Opacity target. State the test and the number — single layer no glow, or transmittance under 5 percent. Not the word "opaque".
  2. Ground construction. Density and yarn count, not just weight. This is the line that decides whether the cloth will pass the backlight test.
  3. Finished weight and panel weight. Both, because the wearer feels the second one.
  4. Drape band. Give a coefficient range or, if that is too technical for the buyer, give a reference sample the mill can match by hand.
  5. Shade and dye depth. Name the shade, and for black specify semi-dull yarn and full penetration rather than a lab-dip number alone.
  6. Shrinkage after three washes, and the finishing route. Pre-shrunk or compacted, with a figure that survives repeated washing rather than one cycle.

Add the face direction — pile out or pile in — and the hem finish, and the brief is complete. Everything else the mill can decide.

A khimar is not a large hijab

The two are often specified together and should not be. A hijab is a square or oblong wrap held close to the head by friction and pins, judged on surface friction, shedding and colour fastness against skin. A khimar hangs from a band and covers shoulders and back without fastening, judged on opacity against daylight, drape under its own weight and length stability after washing.

A cloth that works as a hijab can fail as a khimar for reasons unrelated to quality. A 170 GSM wrap weight with a dense ground may be perfectly opaque in a wrap and too light for a garment that hangs loose and catches sun at the shoulder. The wrap logic is in the hijab fabric guide; the garment specification is the one above.

Where a customer buys both from one programme, the sensible structure is one base cloth in two weights rather than one weight stretched across both end uses. The ground stays the same, which keeps hand and colour consistent, while weight and finish change per garment.

The same logic carries to the outer layer. A khimar worn under an abaya has to sit inside a narrow silhouette without bulk at the shoulder, and pile thickness at that line is what shows. The abaya buyer knows this; the khimar buyer often does not.

Frequently Asked Questions

What velvet is best for a khimar?

A short-pile velvet of 180 to 240 GSM finished, with a densely sett ground rather than a heavy pile. The ground is what blocks light; the pile only supplies colour and surface. Ask for the transmittance figure, not the weight alone.

Why does my black velvet khimar look see-through in sunlight?

Because the ground structure passes light and the skin underneath reflects it back. Red wavelengths survive that round trip better than the rest, which is why a thin black reads brown-red at a low sun. A denser ground in a dark yarn fixes it; a heavier pile does not.

How do I test opacity before ordering?

Fold the sample once, hold it against a window or a torch in a dim room, and look for a glow. One layer glowing means it will read thin outdoors. For a documented figure ask for a 400 to 700 nm transmittance scan: under 5 percent total is solid in daylight.

What GSM for a khimar?

180 to 240 GSM on the finished, relaxed cloth. Weight is judged per garment rather than per square metre: a 2 square metre panel at 200 GSM hangs about 420 g from a 56 cm headband, and the wearer feels that difference at hour six more than the mill does.

Should the pile face in or out on a khimar?

Pile out is conventional: deeper colour, softer light, and less friction as the cloth moves over hair and undergarments. Pile in gives a smoother surface against the skin but reads flat outside. Whichever is chosen, every panel must be cut in the same direction.

How much does a khimar shrink after washing?

Untreated woven velvet shrinks 3 to 5 percent along the warp in a first wash, which is 4.5 to 7.5 cm on a 1.5 m panel. Specify pre-shrunk or compacted finishing for 1 to 2 percent, and ask for the third-wash figure rather than the first.

How many metres of velvet does one khimar take?

1.7 to 2.0 running metres at 140 cm usable width for a standard shoulder-length khimar, including hem allowance and shrinkage margin. Waist-length adds 0.4 to 0.6 m. At 1.8 m average, a 300 metre colour minimum yields roughly 165 garments.

Is a khimar specification the same as a hijab specification?

No. A hijab sits close to the head and is judged on friction, shedding and colour fastness against skin. A khimar hangs loose and is judged on opacity against daylight, drape under its own weight, and length stability after washing. Same cloth family, different requirements.

✉ Inquiry 📱Chat on WhatsApp