Linen-Viscose Slub: Why the Thick-and-Thin Yarn Is the Design

Air-jet looms weaving slub linen-viscose fabric in the Mujia mill

Table of Contents

Introduction

Every few months a container of slub linen-viscose comes back as a claim. The buyer's QC report says the same thing each time: thick places and thin places in the yarn, uneven surface, "yarn quality defect". The photographs are close-ups of exactly the texture the buyer approved on the swatch four months earlier.

This is the most common misunderstanding in the linen business, and it costs both sides money. A slub is not a failure of spinning control. On a fabric sold as slub, the irregularity is the product: it is what gives the cloth its dry, hand-woven look and its lively surface. On a fabric sold as smooth, the same irregularity is a defect and should be rejected. The fabric does not change. The specification does.

This guide is about the second part - how to specify slub so that what arrives is what you approved, and how to tell a designed slub from a genuine spinning fault before you cut. Our own MJ 1212 is a 20% linen / 80% viscose slub at 180 GSM, 140 cm roll width, in 164 in-stock colours at $1.95-2.05 per metre FOB, MOQ 300 m per stock colour. The examples below come from that cloth, but the method applies to any slub fabric you buy.

What a Slub Actually Is

A slub is a place in a yarn where the linear density changes abruptly - a short fat section, usually a few millimetres to a couple of centimetres long, followed by a thin section where the fibre mass was pulled away. In a normal yarn the count varies gently and randomly within a tolerance band. In a slub yarn the variation is deliberate, periodic or semi-random, and far outside that band.

In linen the story has a second layer. Linen is a bast fibre, spun from the stem of the flax plant, and the fibre bundles themselves vary in thickness. Even a carefully spun linen yarn carries natural thick places - the trade calls them neps - where a bundle of fibre ends sits inside the yarn. Viscose, spun from dissolved cellulose, is far more uniform. Blend the two at 20/80 and you get a cloth with three scales of texture at once: the designed slub, the natural linen nep, and the underlying weave. That layered texture is why linen-viscose slub photographs so well and why it is so hard to inspect by eye alone.

The practical consequence: "even" is not the pass criterion for this cloth. The pass criterion is that the irregularity matches the approved sample in size, spacing and frequency, and that the places where the yarn runs thin still have enough strength to survive weaving, finishing and sewing.

Two Kinds of Irregularity, Two Very Different Bills

Not all thick places are equal, and the difference decides who pays.

The first kind is the designed slub, made at the spinning frame by injecting extra fibre into the yarn at controlled intervals, or by running a slub-effect yarn as one component of a folded yarn. It is repeatable: the spinning plan sets the slub length, the pitch between slubs and the increase in diameter. A mill can weave the same slub for years. If a batch deviates from the approved sample, the mill owns the problem.

The second kind is a spinning fault - a drafting fault, a dirty traveller, a sliver irregularity - which produces thick places at random, with no planned pitch and usually a weaker thin place beside them. These are true defects. They break in weaving, they speck the dye, and they are not repeatable because nobody planned them.

On a close-up photo the two look similar. Under a pick glass on the loom, or on a 30 cm length of yarn pulled from the selvedge, they do not. Designed slubs repeat at a pitch; faults cluster. That is the test, and it takes two minutes.

What you see Designed slub Spinning fault
Spacing between thick places Regular pitch, or a planned random band Clusters, long gaps, no pattern
Yarn beside the thick place Normal count, keeps strength Thin place, weak point
Behaviour in weaving Runs clean at production speed Ends break, stops accumulate
Repeatability Same plan next order Cannot be repeated, by definition
Who absorbs the cost Nobody, if the spec is written The mill, if grading is honest

What 180 GSM Slub Does on the Body

Weight decides behaviour, and 180 GSM is a specific place to be. It is heavy enough to hang without clinging, light enough to work for warm-weather garments and for the loose cuts that linen buyers actually sell - wide trousers, camp-collar shirts, kaftans, summer dresses, jumpsuits.

At 140 cm roll width, the constraint is panel width rather than weight. A full-length wide-leg trouser leg or a kaftan body often needs more than 70 cm of usable width, which means two panels or a seam. Plan the marker before you approve the cloth: on this width, garments cut in one piece are usually cut on the cross-grain, and cross-grain cutting on a slub shows the irregularity running across the body instead of down it. That is a design decision, not an error, but it must be made before bulk, not after.

Drape is where linen-viscose earns its price. Pure linen at this weight is crisp and creases sharply; viscose adds fluidity and a cooler touch against the skin, and the 20/80 blend keeps enough linen character that the cloth still reads as linen rather than as a synthetic imitations. It also keeps the crease - buyers who expect the flat, permanent-press look of polyester will be disappointed, and that expectation is better corrected at sampling than at delivery.

Transparency is the third property. A 180 GSM plain weave in a pale shade will shadow against a dark skin tone or a printed underlayer at the shoulder and thigh. Solidity is a function of cover factor, which depends on yarn count and sett as well as weight - so a 180 GSM in a tight sett can be more opaque than a 200 GSM in an open one. If opacity matters, ask for the cover factor or test the actual shade on a body, not on a light table.

Four Checks on a Slub Swatch

You do not need a laboratory to screen a slub fabric. You need a ruler, a pick glass, both hands and ten minutes. Do this on the bulk sample, not on the photo the mill sent.

1. Measure the pitch

Lay the swatch flat and measure the distance between ten consecutive thick places along the warp, then along the weft. Divide by ten. Compare it with the approved sample. Slub spacing that halves or doubles is a different fabric even if the weight is the same - the eye reads pitch, not diameter.

2. Grade the thin places

The failure mode of slub is not the fat place, it is the thin place next to it. Hold the cloth against a window: if the thin places transmit visibly more light, the yarn has been over-drafted to make the slub. On a garment that is where a seam will pull open or a hole will start.

3. Count neps against a standard

Linen neps are natural, but the count per unit area should match the approved sample. A sudden increase means a different linen lot or a lower-grade fibre. A nep board - the trade's comparison card - settles arguments faster than adjectives.

4. Pull a yarn and look at the ends

Unravel 30 cm of weft from the selvedge. Slubs sit in the yarn as a swelling with fibre continuing through it. Faults show as a knot-like tangle with loose fibre ends, or as a thin place where the yarn almost disappears. This one check separates the two categories above better than any lab test.

Where Slub Helps and Where It Hurts

Slub is a surface, and surfaces interact with every process downstream. Knowing where it works saves sampling rounds.

It helps on garments where texture replaces print: solid-dyed kaftans, wide trousers, overshirts, unstructured jackets, home textiles such as cushion covers and light throws. The irregularity hides creases that would look sloppy on a smooth cloth, which is why linen-viscose slub travels well and photographs well after a day of wear.

It hurts in three places. First, fine printing: a digital print on a slub surface loses resolution at the thick places, and registration-critical designs - small geometrics, fine stripes - look broken. Second, tight, structured construction: on a tailored shoulder or a narrow cuff, thick places resist pressing and show as bumps through the interlining. Third, seam slippage: at 180 GSM the yarns are fine, and a slub runs across a seam allowance as an easy path for the yarn to slide. Ask for a seam slippage test on the actual seam type you will sew, not on a generic report.

Embroidery and eyelet work are a separate conversation. Slub gives a hand-worked look under embroidery, but the thick places deflect needles and can distort a fine motif. Test on the real artwork before quoting.

Why the Colour Reads Uneven - and Why That Is the Point

Linen and viscose are both cellulosic, so both take reactive dyes, but they do not take them identically. Linen has a natural grey-yellow cast and a slightly waxy surface; viscose is bright, absorbent and lustrous. Dyed in one bath, the two fibres land a shade or half-shade apart, and because the slub concentrates linen in the thick places, the cloth reads tone-on-tone: darker or warmer at the slubs, cooler in the flat areas.

That is a feature on a solid-dyed slub cloth, and buyers pay for it. It becomes a complaint when a buyer expects a flat, even colour from a photo taken under studio light, or when the same colour is ordered in a different fibre blend for a companion style. Two rules prevent almost all of these disputes: approve the colour on the actual slub substrate, never on a smooth swatch of the same shade; and when a collection mixes slub and smooth cloths, state the acceptable tone difference in the purchase order rather than leaving it to the eye at delivery.

For pale shades, check metamerism as well. A colour matched under the mill's daylight can flip under shop lighting or a phone flash. Approve pale shades under two light sources - daylight and warm indoor light - before bulk, and keep the approved swatch as the reference.

Writing Slub Into the Purchase Order

Most slub claims are specification claims dressed as quality claims. The purchase order fixes that. Six lines do the work:

  • Construction: 20% linen / 80% viscose, plain weave, 180 GSM, roll width 140 cm.
  • Surface: slub effect as per approved sample reference [sample ID and date], slub pitch [measured value] mm warp and weft, nep count per 10 cm as per sample.
  • Fabric character: natural tone variation at slubs is accepted; shade must match the approved swatch under D65 and under warm indoor light.
  • Grading: slub pitch and nep density against the approved sample; genuinely random thick places with adjacent thin places to be graded as defects under the 4-point system.
  • Performance: dimensional change after ISO 6330 method, seam slippage at the specified seam, colour fastness to washing and rubbing.
  • Quantity and price: MOQ 300 m per stock colour, 2,000 m for a custom colour; FOB price and shipment terms; lead time 10-15 days for stock colours, 30-35 days for custom work.

One more line is worth the ink: state that the approved sample is the reference for surface character, and keep a physical sample sealed with the order. A photograph cannot arbitrate a slub dispute. A sealed swatch can.

Care, Shrinkage and the Fifth Wash

Linen-viscose relaxes and shrinks, mostly on the first wash, then behaves. The number that matters for garment costing is the dimensional change measured by the method in your buyer's manual - ISO 6330 domestic washing followed by ISO 5077 measurement - not the number a supplier quotes from memory.

Two practical consequences. First, cut with allowance: if the report says 4% warp and 3% weft, a 100 cm panel must start at about 104 cm, and the marker must be laid out with that assumption rather than discovered at the wash test. Second, tell the customer how to wash it: cool wash, low spin, line dry in shade, warm iron while damp. Viscose loses strength when wet, so a hot tumble dryer is the fastest way to turn a premium cloth into a shrunken one.

Ask also for the pilling and snagging result on the actual slub cloth. Slub surfaces can snag on velcro, on zips and on rough chair edges, and a snag on a slub reads as a pulled thread. A five-wash wear trial on two garments answers more than a page of test data.

Frequently Asked Questions

Is slub a defect or a design feature?

It depends on what was sold. On a fabric specified as slub, the irregularity is the design and the pass criterion is that it matches the approved sample in pitch, size and frequency. On a fabric specified as smooth, the same thick places are defects. Write the specification before the order, seal the sample, and the argument disappears.

How do I tell a designed slub from a spinning fault?

Pull 30 cm of yarn from the selvedge and look at the spacing. Designed slubs repeat at a planned pitch and the yarn beside them keeps its count. Spinning faults cluster randomly and are usually followed by a thin, weak place. Two minutes with a pick glass settles it.

Will the colour be even on a slub linen-viscose?

It will be tone-on-tone, not flat. Linen and viscose take dye differently, and the slub concentrates linen in the thick places, so the cloth reads warmer or deeper at the slubs. Approve the colour on the actual slub substrate, and check pale shades under daylight and warm indoor light before bulk.

Can I print on slub fabric?

Yes, with limits. Large motifs and loose artwork print well and gain a hand-made look. Fine geometrics, small repeats and registration-critical designs lose definition at the thick places. Ask for a strike-off on the actual slub base before committing a print order.

What is the minimum order for a custom colour?

On MJ 1212, 300 m per stock colour from the 164 in-stock shades, and 2,000 m for a custom colour, because a custom shade means a dedicated dye lot. Stock shades ship in 10-15 days; custom dyeing runs 30-35 days. Lab dips are quoted separately and take 5-7 days.

How much will it shrink, and how do I allow for it?

Ask for the dimensional change report on the actual lot, measured by ISO 6330 and ISO 5077. Then build the allowance into the marker: a panel that must finish at 100 cm starts at 100 cm plus the reported percentage. Do not use a number from a previous supplier or a previous blend.

Standards and Test Methods Cited

  • ISO 2060 - Determination of linear density of yarn from packages, the basis for reading slub diameter against base count.
  • ISO 7211-2 - Determination of number of threads per unit length, needed to separate slub effects from sett differences.
  • ISO 13936-2 - Determination of seam slippage, the test that matters most on lightweight slub cloth.
  • ISO 6330 / ISO 5077 - Domestic washing procedure and determination of dimensional change.
  • ISO 105-C06 / ISO 105-X12 - Colour fastness to laundering and to rubbing.

Working on a slub linen-viscose range and want the surface specified properly? Send us the garment, the panel widths and the shade list - we will quote from the 164 in-stock colours and send an A4 swatch of each shade you shortlist.

Mujia Textile — running our own air-jet looms in Zhuji since 2012.

Approve the Slub on Cloth, Not on a Photo.

We send A4 swatches of any shade from the 164 in-stock colours, with the slub pitch marked on the card. Swatches ship the same day.

Request Slub Swatches

More Linen & Linen Blends Guides

Linen Blend Fabric: The Complete Buyer's GuideLinen Cotton Slub Fabric (MJ 5506)Linen Viscose Fabric Buyer's GuideLinen Viscose Sand Washed FabricLinen Curtain Fabric: Weight, Drape and LightLinen Sarong and Head Wrap WeightLinen-Viscose Slub: Why the Thick-and-Thin Yarn Is the DesignLinen Blend Fabric Manufacturer in China
✉ Inquiry 📱Chat on WhatsApp