Printed Double Gauze: Digital Print on Muslin, Artwork to Bulk

Printed cotton double gauze dress in a pink rose floral artwork

Printing on double gauze is not printing on flat cotton with a softer hand. The cloth is two thin gauze layers joined at intervals by a tie-point, which means the printer has to answer a question no flat-cloth printer ever faces: does the artwork go onto one layer before the layers are joined, or onto the assembled cloth after. That single decision changes the look of the reverse side, the registration you can hold, the minimum you can run, and the price per metre.

This guide is the sequence we walk a buyer through when they send a floral file and ask for it on gauze. It is written from the mill side, so the numbers are ours: the printed line M4011-1 runs on a 140 GSM base at 135 cm in three ready colourways, quoted at FOB 1.77 to 2.57 US dollars per metre with a 300 metre per colourway minimum. The solid line it sits beside, M4011, is 125 GSM with 182 in-stock colours and no print pass at all. If you are choosing between the two, the useful comparison is not which looks better in a photo but which one your product can actually carry.

Table of Contents


Printed gauze is not solid gauze with a picture on it

A buyer with a solid gauze programme usually assumes the printed version is the same cloth plus a print charge. It is not, and the difference shows up in three places before you ever discuss price.

The first is the base itself. A solid double gauze can be finished for softness alone: washed, tumbled, crinkled, and shipped. A printed base has to survive a print pass and the curing or steaming that fixes the colour, and it has to come out of that still soft enough to be the product the buyer wanted. In practice this means the base is built slightly heavier and the finishing sequence is re-ordered, which is why our printed line sits at 140 GSM where the solid sits at 125. The 15 GSM is not padding. It is the margin that lets the cloth hold registration and colour without going limp.

The second is the colour system. The solid M4011 carries 182 in-stock colours because a solid shade is a dye recipe that can be repeated on demand. A print is an artwork, and an artwork is a finite set of colourways somebody already developed, matched, and approved. Our printed range currently offers one artwork, a delicate pink rose floral, in three ready colourways: ivory-cream, sky blue and blush pink. That is not a limitation of the mill's capability. It is how print ranges work: the development cost is carried by the colourway, not by the metre, so a range only grows when somebody pays to open a new one.

The third is what the buyer can see. On a solid cloth the whole surface is the colour. On a printed gauze the surface is a ground plus artwork, and the ground is where most complaints originate: a ground that reads cream on the sample and ivory on the bulk roll, a ground that goes patchy where the print pass overlapped, a ground that shows the weave through a large solid area. These are not defects in the usual sense. They are the behaviour of printing on a crinkled two-layer surface, and they are predictable if you know what to ask.

Where the print sits: one layer or both

This is the question that separates a printed gauze order that works from one that comes back. Double gauze is two layers. The artwork has to end up somewhere, and there are three places it can go.

Face layer only, printed after the layers are joined. This is the standard route and the one our ready range uses. The assembled cloth goes through the print line, the artwork lands on the face, and the reverse stays as greige or as the dyed ground. It is the cheapest route, it holds registration well because the cloth is handled as one piece, and it is what almost every dress and blouse programme accepts.

What it does not do is hide. Because the cloth is thin, a dark artwork on a light ground will show a pale ghost of itself through the reverse under strong light. On a dress this is invisible. On a scarf, an unlined jacket, a swaddle that gets held up to a window, or a garment with a rolled cuff, it is visible and it will be noticed. Buyers who have not seen a printed gauze before often read this as a print-through defect. It is not; it is the construction.

One layer printed before joining. Here the face layer is printed flat, then joined to a plain reverse layer at the tie-point. Registration is easier on a flat single layer, and the reverse is deliberately left plain, which reads as intentional rather than as ghosting. The cost is an extra handling step and a narrower set of tie-point patterns that survive printing before joining, because the printed face has to stay dimensionally stable through the join.

Both layers printed, or printed through. This is a different product and should be quoted as one. It is used when the reverse is a design feature: a scarf worn either way, a quilt where the lining shows, a garment with a deep open back. Expect the development to be longer, the minimum to be higher, and the colour match between the two faces to be the thing you inspect hardest, because two printed faces that do not match are far more visible than one printed face and one plain.

Before you send artwork, answer one question in writing: is the reverse of this cloth ever going to be seen by the end customer? If the answer is no, take the standard face-only route and stop worrying about it. If the answer is yes, or even maybe, say so in the inquiry, because it changes which route the mill quotes and it is much cheaper to decide now than to reprint.

Why the printed base runs 140 GSM against 125

Buyers compare the two numbers and ask why the printed cloth is heavier. The honest answer is that the printed cloth has more work to survive.

A 125 GSM two-layer gauze is a light swaddle cloth. It is built to be soft, to drape, to breathe, and to be washed constantly. Its finishing is gentle by design. Put that same base through a print pass and a fixation step and you get a cloth that has been wet, dried, heated and handled twice as many times, and light gauze does not enjoy that. It loses body, the crinkle flattens unevenly, and the print registration drifts because the cloth moves under the screen or the print head.

The fix is not complicated: start 15 GSM heavier. At 140 GSM the same two-layer construction has enough body to hold position through the print line, enough mass to take the fixation heat without collapsing, and enough residual crinkle to still read as gauze when it comes out the other end. The buyer gets a printed cloth that behaves like gauze. The buyer does not get a 125 GSM cloth with a print on it, because that product is not reliably makeable.

This matters when you are costing a programme. If your product spec says 125 GSM and you want it printed, you are either going to be told 140 or you are going to get a cloth that has lost its hand. Neither is a negotiation trick; it is the physics of the process. The useful move is to specify the behaviour you need (drape, opacity, wash durability) and let the weight follow, rather than fixing the GSM and then being surprised by the hand.

It also matters for the solid-versus-printed decision. If a 125 GSM solid gauze already works for your product, printing it changes the cloth. If your product is a dress or a blouse where a little more body is an improvement, the printed version at 140 GSM may actually be the better cloth and not just the decorated one. That is worth testing on a garment rather than judging on a swatch.

The three ready colourways and what they cost

Our printed range is one artwork in three colourways. Being specific about what that means saves a lot of inquiry time.

Item Construction Weight Width Artwork Colourways MOQ FOB
M4011-1 2-layer printed cotton gauze 140 GSM 135 cm Pink rose floral 3 ready: ivory-cream, sky blue, blush pink 300 m per colourway US $1.77–2.57 / m
M4011 2-layer solid cotton gauze, natural crinkle 125 GSM 135 cm — 182 in stock 300 m per colour on request

The FOB band of 1.77 to 2.57 is wide, and buyers reasonably ask which end they are on. Three things move it. Quantity tier is the largest: a 300 metre colourway and a 3,000 metre colourway are not the same price and should not be. Whether the colourway is ready or new is the second: a ready colourway carries no development cost, a new one does, and that cost has to land somewhere. The third is the ground. A pale ground on a light artwork is a shorter, more forgiving print run than a saturated ground that has to stay even across the full width, and the price reflects the pass count.

What the band is not is a negotiation range to be pushed to the bottom of. If a supplier quotes you below the floor of a range like this on a 300 metre order, the saving is coming out of something: the ground coverage, the fixation time, or the fastness. Ask which. A printed gauze that fails a wash test in the customer's hands costs far more than the difference between 1.77 and 2.57.

Artwork: what 300 metres can and cannot carry

The file is not the constraint. The cloth is. A 140 GSM two-layer gauze is a soft, slightly crinkled, slightly translucent surface, and artwork that was drawn for a flat poplin or a paper print will not all survive the translation.

What survives well: medium and large florals with soft edges, watercolour and hand-painted looks, tonal designs where the artwork and the ground sit close together, and anything where a little irregularity reads as charm. Our pink rose floral is in this family deliberately, because a soft-edged floral forgives the surface it is printed on.

What struggles: fine linework under about a millimetre, tight geometric repeats, small text, sharp photographic detail, and designs that depend on exact edge definition. On a crinkled surface a one millimetre line lands on a different plane of the cloth from its neighbour, so it breaks up. It does not look like a printing error. It looks like a blurry design, which is worse, because nobody can point at the defect.

What fails outright: large solid areas of a single saturated colour. The weave shows through, the coverage goes uneven where the print pass overlaps, and the ground reads patchy under raking light. If your design needs a big block of deep colour, gauze is the wrong base and a flat weave is the right one. Saying that early is more useful than printing it and arguing later.

What to send with the file: the repeat size in centimetres, the number of colours, the intended ground colour, and a statement of what the product is and where the reverse will be seen. Production resolution, not a screenshot. Then expect one round of pushback from the mill about which details will not carry at 300 metres. A mill that accepts any file without comment is not being helpful; it is deferring the conversation to the inspection stage, when it is expensive.

Colour fastness: the test that decides a reorder

A first order can be won on the sample. The reorder is won or lost on what happens in the customer's washing machine, and that is a fastness question, not a print-quality question.

Three fastness results matter on printed gauze, and each answers a different worry.

Washing fastness tells you whether the artwork bleeds or fades when the garment is washed the way the care label says. On a light ground with a soft floral this is usually comfortable. On a saturated ground with a dark artwork it is where problems start, because unfixed dye on a thin two-layer cloth has a lot of surface to migrate from. Ask for the grade and the test method together: a grade with no method named is not a number you can compare against another supplier's number.

Rubbing fastness matters more on gauze than buyers expect. A crinkled surface has raised and recessed areas, and a print that sits proud on the raised areas is more exposed to abrasion than a print on a flat weave. Dry rub and wet rub are separate results and both should be on the sheet. A garment that rubs against a bag strap or a car seat is a rubbing test in real life.

Light fastness is the one most often skipped and most often regretted in resortwear. A printed gauze dress sold into a sunny market will be judged on how it looks after a season of daylight, not after one wash. If your product is holidaywear, ask for light fastness explicitly, and ask whether the result is on the bulk lot or on a lab dip.

On the chemistry side, our printed line is OEKO-TEX STANDARD 100 Class II certified under certificate BJ050 121424, produced through our partner dyehouse, Zhejiang Hangmin Printing & Dyeing Branch. Class II covers articles with direct skin contact, which is the right class for a dress, a blouse or a scarf. What the certificate does not do is tell you the fastness grade: those are two different documents and you should ask for both. A certificate proves the chemistry is clean. A fastness report proves the colour stays where it was put. Neither substitutes for the other.

One practical note on the certificate itself. It is issued to a mill and a scope, and the scope is worth reading. A certificate that covers the dyehouse does not automatically cover a different base or a different artwork, and a buyer who needs the paperwork for a customs or retail compliance file should confirm the scope covers the exact item being shipped, not just the mill name on the letterhead.

MOQ and how the tier moves the price

Our printed minimum is 300 metres per colourway. That phrase contains a word buyers routinely misread, so it is worth being blunt about it: per colourway, not per order and not per colour family.

Three ready colourways of one artwork means three separate 300 metre commitments if you want all three. If you want one, the order is 300 metres. If you want the artwork in a fourth colourway that we do not stock, that is a new colourway and it carries development: a lab dip, a match, an approval, and a minimum that is set by the print route rather than by the metre count.

The tier structure is straightforward and worth understanding before you negotiate. At the bottom of the range you are paying for a print run that has to be set up regardless of length: the artwork preparation, the line time, the fixation, the finishing. Those costs are largely fixed, so a 300 metre order carries a disproportionate share of them. As the run length grows, the fixed cost spreads and the per-metre price falls. That is why the quoted band is 1.77 to 2.57 and why asking "what is your best price" without a quantity gets you a polite non-answer.

Two things buyers do that make a small printed order more expensive than it needs to be. The first is splitting one colourway across several shipments: each shipment carries its own setup and its own minimum, so four small shipments can cost more than one larger one. The second is choosing a saturated ground for a test order. A deep ground on a short run is the worst combination, because the pass count is high and the volume that would amortise it is not there. If you are testing a market, test it on a pale ground.

And the comparison worth making: the solid M4011 at 125 GSM carries 182 in-stock colours at 300 metres per colour. If your product does not actually need an artwork, the solid route gives you a much wider palette at a lower price and a shorter lead time. Print is worth paying for when the artwork is the product. It is expensive decoration when it is not.

Sampling: what to ask for before you approve artwork

The sample stage is where a printed gauze order is either de-risked or quietly set up to fail. Four things should be in the package, and a supplier who sends only the first is not giving you enough to decide on.

A strike-off on the actual base. Not on paper, not on a flat cotton substitute. The whole point of printing on gauze is that the surface changes the artwork, so the strike-off has to be on the 140 GSM two-layer cloth that will run in bulk. If a supplier offers a paper proof and says the cloth will be "the same", that is a warning, not a convenience.

A piece large enough to see the repeat and the reverse. A 20 cm swatch hides the two things you most need to judge: whether the repeat reads as a design at garment scale, and what the reverse looks like. Ask for at least a metre, and hold it up to a window.

A washed piece. Half a metre, washed the way the care label will say, then compared against the unwashed half. This is the single most informative thing in the package, because it shows the hand after washing, the shrinkage, and whether the artwork shifts or fades. Buyers who skip this step and approve on an unwashed strike-off are approving a cloth they have not seen.

The test reports for the lot the sample came from. Fastness and, where relevant, the OEKO-TEX scope. A sample with no reports attached is a sample, not a specification.

One more thing worth asking, which almost nobody asks: what the mill's registration tolerance is across the width. On a 135 cm printed gauze, artwork that drifts at the selvedge is a real risk and it is the defect most likely to be argued about at inspection. Get the tolerance in writing before the bulk run, so that inspection has a number to measure against instead of an opinion.

Inspection: what to check on printed rolls

Printed gauze inspection is not the same checklist as solid gauze inspection, and a four-point system alone will not catch the things that actually go wrong. Five checks, in the order that finds problems fastest.

Ground evenness first. Unroll the whole roll and look along it at a low angle under raking light. What you are looking for is patchiness in the ground colour: darker bands where the print pass overlapped, lighter areas where coverage thinned, a drift from one end of the roll to the other. Ground problems are the most common printed-gauze complaint and they are invisible if you only look at a flat swatch.

Registration across the width. Measure the artwork position at the left selvedge and the right selvedge on several points down the roll. If the artwork walks across the width, that is a registration problem and it will show as a seam mismatch in the garment. Compare against the tolerance you asked for at sampling.

Colour continuity between rolls. This is where a printed order differs most from a solid order. Solid dyeing has a shade band system and buyers know to ask for it. Print runs have the same issue and it is less discussed: the first roll and the last roll of a run can differ, and a garment cut across two rolls will show it. Ask for the rolls to be shade-banded and for the band to be marked on the roll ticket, and cut each garment from one band.

Tie-point integrity after printing. The print pass puts the cloth through wet and heat, and the tie-points are the places where the two layers are joined. Check that the tuck points are still holding and evenly distributed, and that the cloth has not delaminated in patches. This is specific to double gauze and it is the check a general fabric inspector will not know to make.

Defect mapping, not just a score. A four-point score tells you how many points per hundred square metres. It does not tell you where they are. On printed gauze, ask for the defects to be marked with stickers at the selvedge and mapped on the roll ticket, so the cutting room can avoid them. A roll that scores acceptably but has its defects clustered in the middle two metres is a roll that will generate waste.

Do this inspection on the bulk lot before shipment if you can, or at least on the first roll of each shade band. The cost of a third-party inspection on a 300 metre printed order is small against the cost of a reprint.

Five mistakes that cost a printed gauze order

These are the five we see most often, in rough order of how expensive they are.

One: approving a strike-off on paper or on flat cotton. The artwork will look crisper than it can ever look on gauze, the buyer approves the crisp version, and the bulk arrives looking softer. Nobody is lying; the reference was wrong. Always approve on the actual base, washed.

Two: not deciding where the reverse will be seen. A face-only print on a garment with a visible reverse produces a ghosting complaint that cannot be fixed after the cloth is woven. Decide this before the inquiry, not after the first shipment.

Three: specifying 125 GSM for a printed programme. The cloth either comes back heavier than specified or comes back limp. Neither is a supplier failure; the spec asked for something the process cannot deliver. Specify behaviour and let weight follow.

Four: a large solid saturated area in the artwork. It will show the weave, it will go patchy where the pass overlaps, and it will be the thing the customer photographs. If the design needs a solid block of deep colour, use a flat weave.

Five: ordering 300 metres in three colourways and calling it a 900 metre order for pricing. It is three separate setups. The price will be three times the small-run price, and treating it as a volume order leads to a negotiation that cannot land. Either commit to a longer run in one colourway or accept the small-run price honestly.

Timeline, realistically

Our quoted lead time on M4011-1 is approximately 10 days after confirmation. That number is real, and it is also the number that most often disappoints, because "after confirmation" is doing a lot of work in that sentence. Here is what sits on either side of it.

Before the 10 days: the strike-off on the base, which is a separate run and typically takes about a week including shipping. The washed sample, if you want it, adds a few days. Approval of the artwork and the colourway is yours to give, and every day it sits in an inbox is a day added to the front of the schedule. A buyer who asks for a strike-off, sits on it for two weeks, then asks for delivery in 10 days is asking for something the calendar does not allow.

After the 10 days: finishing and inspection, packing, and shipping. FOB timing and delivery timing are different numbers and should be quoted as different numbers. On a 300 metre order the production window is short and the logistics window is long; on a 3,000 metre order it inverts. Plan backwards from the date the goods need to leave, not forwards from the order date.

For a ready colourway with an approved strike-off already in hand, 10 days is achievable. For a new colourway or a new artwork, add the development time on the front and do not negotiate it away, because the part that gets compressed when a schedule is squeezed is the fixation, and short fixation is exactly how a fastness failure is manufactured.

The one-paragraph version

Printing on double gauze means printing on two thin layers joined at a tie-point, so the first decision is whether the artwork goes on one layer before joining or on the assembled cloth, and the answer is driven by whether the reverse will ever be seen. Our printed range M4011-1 is a 140 GSM, 135 cm base in one pink rose floral artwork across three ready colourways — ivory-cream, sky blue and blush pink — at FOB 1.77 to 2.57 US dollars per metre with a 300 metre per colourway minimum and roughly 10 days after confirmation. It runs 15 GSM heavier than the 125 GSM solid M4011 because the base has to survive the print pass and still behave like gauze. Approve on a strike-off printed on the actual base and washed, ask for fastness grades with the test methods named alongside the OEKO-TEX certificate rather than instead of it, inspect the ground for evenness and the artwork for registration across the full width, and shade-band the rolls so garments are not cut across two bands. Do those things and a printed gauze order is as predictable as a solid one. Skip them and the cloth will still be beautiful, and the argument will be about whose reference was wrong.

Frequently Asked Questions

Can you print on double gauze?

Yes, and it is a different order from printing on a flat cloth. Double gauze is two lightweight layers joined at intervals by a tie-point, so the printer has to decide whether the artwork goes on one layer before the layers are joined or on the assembled cloth. Our printed line M4011-1 runs on a 140 GSM base at 135 cm in three ready colourways, which is the version we can quote at 300 metres per colourway without new artwork development.

Is the print on one side or both sides?

On our standard printed double gauze the artwork is on the face layer only. Because the cloth is two thin layers, a print that stops at the face can show a pale shadow through the reverse side under strong light, which is normal for the construction and is what most garment buyers accept for dresses and blouses. If your product is worn with the reverse visible, say so before the order, because a print-through or a both-layer print is a different process with a different cost.

What is the minimum order for printed double gauze?

300 metres per colourway on our ready range, which is three colourways of one pink rose floral artwork at 140 GSM. A new artwork is a separate question: the minimum depends on whether the screen or digital route is used, and below-minimum work is charged per colourway rather than per metre. If you are testing a market, taking one ready colourway inside a larger order is usually cheaper than opening a small custom lot.

How much does printed double gauze cost?

Our M4011-1 range quotes at FOB 1.77 to 2.57 US dollars per metre, and the spread is driven by quantity tier and by how much of the artwork is a new development rather than a ready colourway. Compare that with the solid M4011 at 125 GSM, which carries 182 in-stock colours and no print pass. The 15 GSM difference between the two is not waste: a heavier base is typically specified to carry the extra print and finishing passes, though the figure is a mill decision, so confirm the base for your artwork rather than assuming ours applies to another printer.

Does the print survive washing?

It depends on the dye class and the finishing, not on the word digital. Ask for the colour fastness figures on the bulk lot rather than the sample: washing, rubbing and light, each with the test method named. Our printed line is OEKO-TEX STANDARD 100 Class II certified, certificate BJ050 121424, through our partner dyehouse, which covers the chemistry on skin-contact goods; it does not by itself tell you the fastness grade, so ask for both.

Can I use my own artwork?

Yes, and the constraint is the cloth, not the file. A two-layer gauze at 140 GSM is a soft, slightly crinkled surface, so fine linework and small repeats lose definition and large solid areas show the weave through the colour. Send the file at production resolution with the repeat size and the number of colours stated, and expect the mill to tell you which details will not survive at 300 metres rather than reproduce them badly.

Mujia Textile — running our own air-jet looms in Zhuji since 2012.

Printed Gauze — Send the Artwork, Get a Strike-Off Quote.

Tell us the finished product, whether the reverse will be seen, and the repeat size. We will tell you which details will not carry on a 140 GSM two-layer base, then quote FOB within 24 hours. MOQ 300 m per colourway, approx. 10 days.

Send Artwork for Review

More Muslin & Double Gauze Guides

M4011-1 Printed Double Gauze — Product Page Muslin Fabric Sourcing: Layers, Weight, Cost and Inspection Double Gauze Tie Points: Where the Two Layers Meet 182 Colours on the Plain Crinkle Base Why Double Gauze Gets Softer After Washing Double Gauze Pilling Test: Reading the Grades Baby-Grade Double Gauze: Which Documents Travel Seersucker or Double Gauze? The Inquiry Word Decides the Quote Muslin for Bath and Nappy Use: Absorbency and Edges Printed Poplin: Rotary Stock Print vs DigitalHow to Buy Swim Knit: Four Tests Before a Reorder
Get a Quote